I think I may have misunderstood and maybe someone might confirm one way or another.  I thought that the two default units in the Carenado PC 12 were replaced with the GTNXi 750 and 650.  However when I enable the GTNXi in the ipad on the aircraft, only the 750 is installed leaving the default smaller unit in place.

Also, I have to go through the process of loading the unit each time I start the sim.  Is there any way of keeping they unit in nthe aircraft until I decide to remove it?

Many Thanks

Shugsta

Hello all. I made a checklist to the C-310R, put it on: C:\ProgramData\TDS\GTNXi\C-310 Normal Procedures.ace
The GTNXi don't show the checklist nor on the aircraft or the Garmin trainer.
What I'm doing wrong?

Thanks in advance.

Can I run TDS on a separate computer the way Air Manager does?

Hello,
sorry for my English,
I bought Milviz 310R, and installed TDS GTNXi 750.
I launched TDS GPS Manager and  installed GTNXi PC trainer and TDS GTNXi.
In Garmin aviation trainer I selected multi engine turboprop.
Navigators - GNTXi (V20.20) - display (nothing) and Power on.
A full of messages errors - 
failed to load iop_b.dll getlasterror 126
iop_c.dll, iop_d.dll, iop_com.dll, iop_nav.dll, nav_main.dll......ETC all DLL with getlasterror 126.

Help me please

Attached Files

  TDSGPSManager.txt (Size: 1,008 bytes / Downloads: 1)
  TDSGTNXi650Unit1Log.txt (Size: 132 bytes / Downloads: 0)
  TDSGTNXi750Unit1Log.txt (Size: 132 bytes / Downloads: 1)
  TDSGTNXi750Unit2Log.txt (Size: 33.16 KB / Downloads: 1)
  TDSGTNXiExeLog.txt (Size: 1.02 KB / Downloads: 1)

Hi, the software has been working great (no problems) since I purchased a few months ago but I noticed there was an update recently for trainer (I'm on 3.2.3.0) but I've tried a dozen times now to update and it gets to around 15-19% and then the program simply stops and says 0 mins left.  When I try to quit the update program windows says program is not responding so it force closes it.

I was able to update the other part to 1.0.1.9 (since it was quick) but have been unable to update the trainer module.  Any ideas? 

Thank you.

Hello,

Tried loading the 750 with the above airplane in MSFS2020, and it loads on the panel, but it does not turn on with the avionics master switch. Tried clicking all buttons on the unit, but I cannot get it to turn on. What am I missing? Thanks.

Ray

Good Morning,

I have been at this for hours. I have tried just about everything but drinking heavily. I have read post after post deleted reinstalled and just about given up.
The same problem as everyone else, If I check in settings for either the 650 or 750 "hide window frame" the screen disappears.
 This is how I try to set up the RSG GTN750 and 650. I open "C:\Users\XXXX\AppData\Roaming\Microsoft\Windows\Start Menu\Programs\TDS\TDS GTNXi Flight Sim.lnk" on my main screen. I then click or turn on the 750 or 650 it opens in windowed mode. I then make it fit my main screen and drag it still in windowed mode to either the RSG 750 or 650 depending on which I'm setting up. I then close the window by clicking the corresponding avionics picture in the TDS program. I then go to the settings for one or the other 650, 750 and check hide window frame. 
I then proceed to pull out my hair.
I think I got it although I don't know how.
750 has a database and map but 650 does not anyone know why? Did I install the trainer correctly?

Good evening,

I have searched forums and nothing helped. I have added exceptions for MSFS, TDS, trainer and everything else as per forum posts, but Windows Defender still clogs the CPU as soon as GTN is running in any plane. If I disable real time protection, it works fine, but then I am not protected.

Having thought we had resolved this issue thanks to your support staff I know find it has returned after most recent attempt to update to 1.0.1.9 from ...1.8

I receive the following error:  Install Error TDSGTNXiFlightSimEXE.exe...SimConnect.dll

The guages work find when MSFS2020 is off.

Assistance appreciated

Bob Goodwin

In real life I push the lower right button to switch between COM and NAV frequencies but it does not work here. I don't use an integrated GTN 650 but separate on a separte screen.