Hi,

Since installing the TDS GTNXi software and the RV 14 combination into MSFS 2020, I have been getting the following message every time I start up the simulator:

"We have detected that Windows Hardware-accelerated GPU scheduling is turned ON"  

SEE ATTACHED JPG

After removing the TDS GTNXi and RV 14 modules from the Community Folder, this message still comes up.

Is this an issue you plan to fix in the future, if not, how do I remove prevent this error message from returning?

William Clark

Attached Files

Thumbnail(s)
   

Here is my thread over my problems with the TDS GTNXI Flight sim 
 
I installed the Chessna 414AW in MSFS. With TDSGPS manager I installed the Garmin  Aviation Trainers and the TDS GTNXI Flight sim. After the software was installed I started MSNFS2020. Loading Cessna 414 N427RC GTN750XI and I started the TDS GTNXI Flight sim. TDS GTNXI flight sim was connected and in Gauge mode.

 I replaced de tds-gtnxi-gauge file from the Community folder. After a restart from msds2020 and loading the Cessna 414 N427RC GTN750XI and the TDS GTNXI Flight sim and de sim was connected and not in Gauge mode. I don't use VC.

After starting the Cessna 414 N427RC GTN750XI the plane was ok but the screen was black

Can you help my?

Attached Files

Thumbnail(s)
           

Hello,
I can't understand all of them.
I installed via TDS GPS Manager the Trainer as well as the GTNXI for MSFS.
When I run the Cessna 414, the 750XI works fine. I would like to have it on my tablet. So I have to use the trainer? Who will be connected to MSFS? When I launch the trainer, I have an error: Unable to communicate with trainer: Unable to open interface error code 2.
I'm doing something wrong, but I don't know what.
Sorry for the English... and thanks for the help.

Are europe charts planed for future updates???

Regards
Andreas

Hi, have searched here and around the nets for a solution, however not successful.  I purchased both the TDS GTN and Flysimware Cessna 414 yesterday.  Installed everything in order per instructions, the TDS guage loads during msfs boot etc... But, not getting a load in the GTN screen in aircraft.  When I turn on avionics power, the small units above the large GTN screens do power, and the IDENT powers when the on button is pushed, but no large GTN screen load.   I have completely uninstalled and reinstalled a couple of times, no luck.  Note, I have installed the latest versions of both products as of this post date.

Would appreciate any help, thanks.

I'm not able to change the volumen when the TAWS test say its OK, or terrain alert!!

By the way, sorry for add more questions but, is there an option for, on the C414, the two 750xi follow the SAME FPL???

Thanks!!

Simworks Studios has released their RV14 which comes with a TDS GTN integration option.

Unfortunately, the LPV glideslope indicator stays pegged at the bottom on the PFD..

A workaround is to display the Loc and GP needles on the standby indicator.

See here for details:  https://www.avsim.com/forums/topic/61758...tds-gtnxi/

I wonder that via the manager version 1.0.1.3 is installed and no word about it here in the forum!
No info no changelog...

Greetings.

The vertical component of an approach no longer works. There aircraft with this latest 1.43 version now takes it upon itself to not follow the "glide path", both precision and non precision approaches. 

it goes below the GP and starts a decent into the ground short of the runway.

Good morning all. Brand new user. I am using the GTNXi in the new Flysimware C414. When autopilot is on and I am attempting to increase my altitude, I am only able to increase it by only several hundred feet, maybe a thousand. Then it stops. I need to deactivate then reactivate the altitude button if I want to increase it more.

I have been searching and cant seem to find any other related topics about this. Has anyone else experienced this, or maybe I am just doing something wrong.

I also understand that the 414 is still in Beta, so maybe it's just not working at the moment.

Thanks for listening.