I just downloaded the new version of Just Flight PA28 Turbo Arroow IV and I get black screens in game. 

The trainer works externally and if I press "Alt.Gr" and click on the GTN 750 you can see that it is active but it does not show in the cockpit integration.

What could be wrong?

It does work on other airplanes it is just this one that I cant make it work.

Edit: If I start it on the runway it does work, it is from cold and start it does not power up

Attached Files

Thumbnail(s)
       

Hi,
After yesterday's successful flight, today the TDS GTN 750 screens are all black.

I found the thread about reinstalling and rebooting the latest version 1.2.0.8 as an administrator. I did all that, but it did not help.

I made sure that Avionica Master is on and giving power (by switching back to the GNS in the Miviz 310), but the GTN 750 stays black. I tried the Milviz 310 and the SWS C414 (yes, correct livery selected).
Any help is appreciated.

Running FS 2024 1.4.18.0
Windows 11 24H2

I purchased the Carenado F33A for MSFS 2024 on the marketplace. Even though I have downloaded and installed TDSGPSManager v. 1.0.1.4 and installed the v.1.2.0.8 of the gauge, the Asobo EFB in the F33A shows the TDSGTN as Uninstalled. Anyone see this behavior? Any solution?

Good day,

I installed the TDS software and reinstalled since I was having issues but that did not solve my problems. First item is that when I launch the TDS Flight sim (version 1.2.0.8) I have to check the external hardware compatibility box each time, I use 1 GTN650 from realsimgear. Second issue is that upon each relaunch of the software I have to maximize the window on the 650 display. And last issue is that the TDS software crashes upon launch of MSFS2020.
Thanks for any feedback.
Greetings
Marnix

Upgraded this morning.  I had to disable my anti-virus to get it to install (not required on previous TDS versions).
The update says successful, tdsgtnxi loads, all buttons appear to work, except the continue button.  Cant get past that screen on gtn750 and 650.  Worked fine in previous version.
This is in the Thranda Pilatus PC12.  Was going to try to install previous version, but that's not an option in the installer.

Attached Files

Thumbnail(s)
       

Hi,

Had this problem before but it magically started working. However, the problem is back again.

I start msfs2020 and i see the splash screen for TDS GPS GTNXi when msfs2020 is loading.
I now launch the Cessna 414 AW selecting the TDS GTNXi 750 livery of the plane.
The C414 AW loads up and the GPS GTNXi screens are black. This is normal. 
I switch on the battery and the avionics switch and now i expect the GPS GTNXi 750 to start up but nothing happens. Both screens just stay black.

Before i tested again i have updated TDS as much as i can. Both the trainer and the msfs2020 part as well as the GPS manager. See picture.

I tried to load the PMS50 GTN750 livery and now the screens start but i could not use GPS for navigation. Only VOR navigation would work. In GPS mode, when i pressed NAV on the autopilot, nothing happened. Also , the maps screens were showing the background fine but the magenta route lines were flickering. In GPS mode, the needle on the HSI was vibrating. 

I also include a picture of the cockpit when i am using the GTNXi 750 and after i have switched on the battery and avionics.
Perhaps not interesting but when i switch on the avionics , the autopilot shows 3 red lights like it's doing a self test before they go out.

Best Regards / Jan

Attached Files

Thumbnail(s)
       

Hi, I need to reinstall the SW but I got an error regarding the maximum number of installations, can you help me? This will be the last installation.
Thanks!

Attached Files

Thumbnail(s)
   

Have software installed and shows connected to MSFS 2020. The interface screen shows "TDS GTNXi in Gauge Mode", but Flysimware Sierra C24R 750 screen stays blank.  Steam community folder has tds-gtnxi-gauge folder listed. Alos the interface screen doesn't allow me to select settings or any other buttons. I appreciate your help.

Hello Team,
I’m really in love with TDS GTN for Xplane as I now can really use an up-to-date GTN with Xplane! 
Everything is OK with XP12 generic Cessna.

I am experiencing issues with Torquesim SR22s Avidyne Entegra:
It seems that there’s an issue with the datas feeding the GTN.
While following an FPL or an approach, there’s a 15 degrees right error on the GPS course and no distance. Everything is ok on the GTN screen.
Dis somebody experiences such an issue? (No problem with GNS and this package).
I will do other tests with all the SR22s of the package (Stec and GFC90 autopilot with SR22 and SR22T) but last time it was the case for both.

If nobody experienced this I will try to post screenshots.
Thanks
Greetings from France
Fred

Okay thanks.  I successfully changed my password.  I really appreciate your help. I have been an active flight simulator since 1984, and my old brain is a "little" slower than it used to be. I still love this hobby, and your software make it even better.  Please advise how I download and install the latest version of TDS GTNXI XPlane.

Thanks a lot,
Howard Bloom